第一次执行nandinstall提示重启后又执行了一次nandinstall，后来提示完成关机拔掉sd卡，拔掉后开机就是下面得过称：
=========== WLAN placed in RESET ========
[ ok ] All processes ended within 2 seconds...done.
[ ok ] Stopping enhanced syslogd: rsyslogd.
<7>wlan1: deauthenticating from 26:2f:68:01:3d:a0 by local choice (reason=3)
<6>cfg80211: Calling CRDA for country: US
[....] Deconfiguring network interfaces...Internet Systems Consortium DHCP Client 4.2.2
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/wlan0/02:1a:11:fc:69:c7
Sending on LPF/wlan0/02:1a:11:fc:69:c7
Sending on Socket/fallback
DHCPRELEASE on wlan0 to 192.16.137.1 port 67
send_packet: Network is unreachable
send_packet: please consult README file regarding broadcast address.
Internet Systems Consortium DHCP Client 4.2.2
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/wlan1/c8:3a:35:cb:25:d2
Sending on LPF/wlan1/c8:3a:35:cb:25:d2
Sending on Socket/fallback
DHCPRELEASE on wlan1 to 192.16.137.1 port 67
send_packet: Network is unreachable
send_packet: please consult README file regarding broadcast address.
done.
[info] Saving the system clock.
<6>sunxi-rtc sunxi-rtc: actually set time to 2014-2-15 9:47:59
[info] Hardware Clock updated to Sat Feb 15 17:47:59 CST 2014.
[ ok ] Unmounting temporary filesystems...done.
[ ok ] Deactivating swap...done.
[ ok ] Unmounting local filesystems...done.
<6>EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[info] Will now halt.
<5>sd 0:0:0:0: [sda] Synchronizing SCSI cache
<5>sd 0:0:0:0: [sda] Stopping disk
<6>[sw-ohci2]: shutdown start
[sw-ohci2]: close clock
<6>[sw-ohci2]: shutdown end
<6>[sw-ehci2]: shutdown start
[sw-ehci2]: Set USB Power OFF
[sw-ehci2]: close clock
<6>[sw-ehci2]: shutdown end
<6>[sw-ohci1]: shutdown start
[sw-ohci1]: close clock
<6>[sw-ohci1]: shutdown end
<6>[sw-ehci1]: shutdown start
[sw-ehci1]: Set USB Power OFF
[sw-ehci1]: close clock
<6>[sw-ehci1]: shutdown end
[NAND]shutdown
nand try to shutdown 0 time
Nand flash shutdown ok!
<0>Power down.
[ 117.090316] Power down.
<6>[hotplug]: cpu(0) try to kill cpu(1)
<3>[hotplug]: try to kill cpu:1 failed!
[axp] send power-off command!
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =2048
sum=0xeb005a18
src_sum=0xeb005a18
Ready to disable icache.
Jump to secend Boot.
[ 0.155]
U-Boot 2011.09-rc1-00003-ge89ab14-dirty (Jan 03 2014 - 12:57:33) Allwinner Technology
[ 0.164]version: 1.1.0
[ 0.167]pmbus: ready
[ 0.272]PMU: AXP209
[ 0.275]PMU: AXP20x found
[ 0.278]PMU: bat ratio = 100
[ 0.281]after set, dcdc2 =1400mv
[ 0.285]PMU: dcdc2 1400
[ 0.287]PMU: pll1 912 Mhz
boot_clock = 912
dcdc2_vol = 1400
[ 0.295]after set, dcdc2 =1400mv
dcdc3_vol = 1250
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 0
storage_type = -1
usb_recovery = 1
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[ 0.331]DRAM: 2 GiB
relocation Offset is: 75b23000
donn't initialize ther user_gpio (main_key:boot_init_gpio)
DRV_DISP_Init: opened
[ 0.546]boot_disp.output_type=4
[ 0.549]boot_disp.output_mode=4
[ 0.552]boot_disp.auto_hpd=0
workmode = 0
[ 0.557]NAND: NAND_UbootInit
NB1 : enter NAND_LogicInit
nand : get id_number_ctl from script, 3
not burn nand partition table!
NB1 : nand_info_init fail
[ 6.315]nand init fail
set to recovery
try sprite_led_gpio config
sunxi sprite begin
screen_width = 1024
screen_height = 768
bar x1: 256 y1: 344
bar x2: 768 y2: 424
read mbr failed
sprite update error: no data part found
read mbr failed
sprite update error: read image start error
sprite update error: current card sprite failed
now hold the machine
fail to find part named env
Using default environment
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_nand
key 0
recovery key high 6, low 4
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_nand boot_normal
the part isn't exist
WORK_MODE_BOOT
WORK_MODE_BOOT
[ 6.409]Hit any key to stop autoboot: 0
cant find part named boot
sunxi_flash - sunxi_flash sub-system
Usage:
sunxi_flash read command parmeters :
parmeters 0 : addr to load(hex only)
parmeters 1 : the name of the part to be load
[parmeters 2] : the number of bytes to be load(hex only)
if [parmeters 2] not exist, the number of bytes to be load is the size of the part indecated on partemeter 1
boota: bad boot image magic, maybe not a boot.img?
sunxi#
|
|Archiver|手机版|粤ICP备13051116号|cubie.cc---深刻的嵌入式技术讨论社区
发表于 2014-2-15 17:51:14
发表于 2014-5-28 09:58:04