CT的wifi连了两次重启了两次又挂了。。。

gsoft

重刷了重新敲命令彻底不行。。。固件是这个：ct-lubuntu-nand-v1.00/lubuntu-desktop-nand.img

1. root@cubietruck:~# modprobe bcmdhd
   
2. <6>bcmdhd: got gpio2, mapped to irqno170
   
3. dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to turn on WL_REG_ON
   
4. <6>sdio wifi power state: on
   
5. <6>[mmc-msg] sdc3 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
   
6. <6>[mmc-msg] sdc3 power on
   
7. <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
   
8. <6>[mmc-msg] sdc3 set round clock 400000, src 24000000
   
9. <3>[mmc-err] smc 3 err, cmd 52,  RTO
   
10. [  251.633098] [mmc-err] smc 3 err, cmd 52,  RTO
    
11. <3>[mmc-err] smc 3 err, cmd 52,  RTO
    
12. [  251.641706] [mmc-err] smc 3 err, cmd 52,  RTO
    
13. <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
    
14. <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
    
15. =========== WLAN placed in POWER ON ========
    
16. <3>[mmc-err] smc 3 err, cmd 8,  RTO
    
17. [  251.695173] [mmc-err] smc 3 err, cmd 8,  RTO
    
18. <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
    
19. <4>mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
    
20. <4>mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
    
21. <4>mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
    
22. <4>mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
    
23. <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
    
24. <6>[mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
    
25. <6>[mmc-msg] sdc3 set round clock 42857143, src 600000000
    
26. <6>[mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
    
27. <6>mmc1: new high speed SDIO card at address 0001
    
28. Linux Kernel SDIO/MMC Driver
    
29. 
    
30. Dongle Host Driver, version 1.28.23.3 (r)
    
31. Compiled in drivers/net/wireless/bcmdhd on Oct 26 2013 at 18:32:47
    
32. <6>bcmdhd: irq=170, flags=0x00000414
    
33. dhdsdio_probe : no mutex held. set lock
    
34. F1 signature read @0x18000000=0x1591a962
    
35. bcmsdh_config_hw_oob_intr: Enter
    
36. DHD: dongle ram size is set to 245760(orig 245760)
    
37. dhd_attach, firmware path
    
38. wl_create_event_handler thr:7dc created
    
39. wl_create_event_handler thr:7dc started
    
40. p2p0: P2P Interface Registered
    
41. dhd_attach thr:7de created
    
42. dhd_attach thr:7de started
    
43. dhd_attach thr:7e1 created
    
44. dhd_attach thr:7e1 started
    
45. dhd_attach thr:7e2 created
    
46. dhd_attach thr:7e2 started
    
47. Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
    
48. dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to insert WLAN RESET
    
49. dhdsdio_probe : the lock is released.
    
50. <6>sdio wifi power state: off
    
51. =========== WLAN placed in RESET ========

复制代码

fkpwolf

我也是，感觉失败后重启和掉电后重启的错误信息还不一样，一个可以创建wlan0，一个就是通篇错误。

txx

我继续观望好了...不去折腾他了 还是先研究GPIO吧..