Cubieboard1智能云计划开启！

tll

因为前面我跟大家说过，Cb1我不打算继续支持它的CbOS了，所以我决定，拿他当Cloud Server
以前智能家居的帖子我也发了，后面因为手机升级了iOS7，siriproxy不能用了，所以暂停了。
我现在给cb弄了个盒子，准备安装smb，开始计划咯～
这是盒子，本来里面装姜母鸭的：

亮亮的，看到了吗

里面其实有个灯

上面写的是Cubie，用电烙铁切的，万能烙铁，被我拿去焊锡，切亚克力，切塑料，熔松香粘

然后ssh登录，我这是有给cb固定ip的，105
因为以前不玩文件共享，所以这是第一次安装samba:

1. apt-get install samba -y
   

复制代码

顺便说下，我用mac系统，没法使用这个协议，因此安装另一个软件——vsftpd

1. apt-get install vsftpd -y
   

复制代码

我的配置：

1. # Example config file /etc/vsftpd.conf
   
2. #
   
3. # The default compiled in settings are fairly paranoid. This sample file
   
4. # loosens things up a bit, to make the ftp daemon more usable.
   
5. # Please see vsftpd.conf.5 for all compiled in defaults.
   
6. #
   
7. # READ THIS: This example file is NOT an exhaustive list of vsftpd options.
   
8. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
   
9. # capabilities.
   
10. #
    
11. #
    
12. # Run standalone?  vsftpd can run either from an inetd or as a standalone
    
13. # daemon started from an initscript.
    
14. listen=YES
    
15. #
    
16. # Run standalone with IPv6?
    
17. # Like the listen parameter, except vsftpd will listen on an IPv6 socket
    
18. # instead of an IPv4 one. This parameter and the listen parameter are mutually
    
19. # exclusive.
    
20. #listen_ipv6=YES
    
21. #
    
22. # Allow anonymous FTP? (Beware - allowed by default if you comment this out).
    
23. anonymous_enable=YES
    
24. #
    
25. # Uncomment this to allow local users to log in.
    
26. local_enable=YES
    
27. #
    
28. # Uncomment this to enable any form of FTP write command.
    
29. write_enable=YES
    
30. #
    
31. # Default umask for local users is 077. You may wish to change this to 022,
    
32. # if your users expect that (022 is used by most other ftpd's)
    
33. local_umask=077
    
34. #
    
35. # Uncomment this to allow the anonymous FTP user to upload files. This only
    
36. # has an effect if the above global write enable is activated. Also, you will
    
37. # obviously need to create a directory writable by the FTP user.
    
38. #anon_upload_enable=YES
    
39. #
    
40. # Uncomment this if you want the anonymous FTP user to be able to create
    
41. # new directories.
    
42. #anon_mkdir_write_enable=YES
    
43. #
    
44. # Activate directory messages - messages given to remote users when they
    
45. # go into a certain directory.
    
46. dirmessage_enable=YES
    
47. #
    
48. # If enabled, vsftpd will display directory listings with the time
    
49. # in  your  local  time  zone.  The default is to display GMT. The
    
50. # times returned by the MDTM FTP command are also affected by this
    
51. # option.
    
52. use_localtime=YES
    
53. #
    
54. # Activate logging of uploads/downloads.
    
55. xferlog_enable=YES
    
56. #
    
57. # Make sure PORT transfer connections originate from port 20 (ftp-data).
    
58. connect_from_port_20=YES
    
59. #
    
60. # If you want, you can arrange for uploaded anonymous files to be owned by
    
61. # a different user. Note! Using "root" for uploaded files is not
    
62. # recommended!
    
63. #chown_uploads=YES
    
64. #chown_username=whoever
    
65. #
    
66. # You may override where the log file goes if you like. The default is shown
    
67. # below.
    
68. #xferlog_file=/var/log/vsftpd.log
    
69. #
    
70. # If you want, you can have your log file in standard ftpd xferlog format.
    
71. # Note that the default log file location is /var/log/xferlog in this case.
    
72. #xferlog_std_format=YES
    
73. #
    
74. # You may change the default value for timing out an idle session.
    
75. #idle_session_timeout=600
    
76. #
    
77. # You may change the default value for timing out a data connection.
    
78. #data_connection_timeout=120
    
79. #
    
80. # It is recommended that you define on your system a unique user which the
    
81. # ftp server can use as a totally isolated and unprivileged user.
    
82. #nopriv_user=ftpsecure
    
83. #
    
84. # Enable this and the server will recognise asynchronous ABOR requests. Not
    
85. # recommended for security (the code is non-trivial). Not enabling it,
    
86. # however, may confuse older FTP clients.
    
87. #async_abor_enable=YES
    
88. #
    
89. # By default the server will pretend to allow ASCII mode but in fact ignore
    
90. # the request. Turn on the below options to have the server actually do ASCII
    
91. # mangling on files when in ASCII mode.
    
92. # Beware that on some FTP servers, ASCII support allows a denial of service
    
93. # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
    
94. # predicted this attack and has always been safe, reporting the size of the
    
95. # raw file.
    
96. # ASCII mangling is a horrible feature of the protocol.
    
97. #ascii_upload_enable=YES
    
98. #ascii_download_enable=YES
    
99. #
    
100. # You may fully customise the login banner string:
     
101. #ftpd_banner=Welcome to blah FTP service.
     
102. #
     
103. # You may specify a file of disallowed anonymous e-mail addresses. Apparently
     
104. # useful for combatting certain DoS attacks.
     
105. #deny_email_enable=YES
     
106. # (default follows)
     
107. #banned_email_file=/etc/vsftpd.banned_emails
     
108. #
     
109. # You may restrict local users to their home directories.  See the FAQ for
     
110. # the possible risks in this before using chroot_local_user or
     
111. # chroot_list_enable below.
     
112. chroot_local_user=YES
     
113. #
     
114. # You may specify an explicit list of local users to chroot() to their home
     
115. # directory. If chroot_local_user is YES, then this list becomes a list of
     
116. # users to NOT chroot().
     
117. # (Warning! chroot'ing can be very dangerous. If using chroot, make sure that
     
118. # the user does not have write access to the top level directory within the
     
119. # chroot)
     
120. #chroot_local_user=YES
     
121. chroot_list_enable=YES
     
122. # (default follows)
     
123. chroot_list_file=/etc/vsftpd.chroot_list
     
124. #
     
125. # You may activate the "-R" option to the builtin ls. This is disabled by
     
126. # default to avoid remote users being able to cause excessive I/O on large
     
127. # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
     
128. # the presence of the "-R" option, so there is a strong case for enabling it.
     
129. #ls_recurse_enable=YES
     
130. #
     
131. # Customization
     
132. #
     
133. # Some of vsftpd's settings don't fit the filesystem layout by
     
134. # default.
     
135. #
     
136. # This option should be the name of a directory which is empty.  Also, the
     
137. # directory should not be writable by the ftp user. This directory is used
     
138. # as a secure chroot() jail at times vsftpd does not require filesystem
     
139. # access.
     
140. secure_chroot_dir=/var/run/vsftpd/empty
     
141. #
     
142. # This string is the name of the PAM service vsftpd will use.
     
143. pam_service_name=vsftpd
     
144. #
     
145. # This option specifies the location of the RSA certificate to use for SSL
     
146. # encrypted connections.
     
147. rsa_cert_file=/etc/ssl/private/vsftpd.pem

复制代码

之后可以用user用户登录，账户允许chroot文件：

1. root@cubieboard:~/source_code/cloudserver# cat /etc/vsftpd.chroot_list
   
2. user
   
3. root@cubieboard:~/source_code/cloudserver#

复制代码

试了下phpmailer，没成功，就是一直卡着，不知道为啥
然后我自己写的ledc程序，用cron启动，每5分钟ping一次谷歌，当然我觉得ping百度更好，因为谷歌有时候不通，通就亮灯，不通灭灯，通过GPIO控制，引入的文件就是gpio的控制文件

1. #include <stdlib.h>
   
2. #include <stdio.h>
   
3. #include "gpio_lib.c"
   
4. #include <string.h>
   
5. 
   
6. int dy(int port)
   
7. {
   
8.     //printf("SUNXI GPIO tool\n");
   
9.     if(SETUP_OK!=sunxi_gpio_init()){
   
10.         printf("Failed to initialize GPIO\n");
    
11.         return 1;
    
12.     }
    
13.    
    
14.     if(SETUP_OK!=sunxi_gpio_set_cfgpin(SUNXI_GPD(port),OUTPUT)){
    
15.         printf("Failed to config GPIO pin\n");
    
16.         return 1;
    
17.     }
    
18.    
    
19.     if(system("ping google.com -c 1") != 0){
    
20.         //Is network OK?
    
21.     printf("No network!\n");
    
22.     if(sunxi_gpio_output(SUNXI_GPD(port),LOW)){
    
23.         printf("Failed to set GPIO pin value\n");
    
24.         return 1;
    
25.     }
    
26.     }else{
    
27.         printf("Fine!\n");
    
28.         if(sunxi_gpio_output(SUNXI_GPD(port),HIGH)){
    
29.             printf("Failed to set GPIO pin value\n");
    
30.             return 1;
    
31.         }
    
32.     }
    
33.     sunxi_gpio_cleanup();
    
34.     return 0;
    
35. }
    
36. 
    
37. int main(int argc,char* argv[]){
    
38.     dy(0);
    
39. }
    

复制代码

用crontab -e编辑文件，增加：

1.   */5 *   *   *   *    /root/source_code/cloudserver/ledc > /tmp/netlog
   

复制代码

好了，大家慢慢玩～

SUNROC1

顶一下      

xfire

真是个盒子