新鲜出炉：从零构建CubieBoard Debian Linux

realm520

soloforce 发表于 2013-10-2 21:56
我一直都是小写的，cb1和cb2都是，也能编译通过

首先谢谢你的文档,我第一次玩这个。
关于这个错误,我估计是最近的Makefile有些变动吧.我再试了一次,确实小写不行,报这个错.
make: *** No rule to make target `cubieboard_config)', needed by `cubieboard'.  Stop.
我也是随便猜了一下,改首字母大写就OK了.

另外,建议在前面加一个步骤,编译sunxi-tools下面的工具，可以放在clone完以后。其实在后面有提到：
如果需要重新分区的话可以用 nand-part 工
具，在 sunxi-tools 里面可以找到，可能要自行编译。
不过我觉得放前一点好些，因为第一次照这个文档做的时候，这些工具都是要自己编的。我就是找不到fex2bin工具，然后find了所有目录，并看了相关的Makefile，才发现需要自己编。

再次感谢提供如此详细的文档。我已经把需要的文件都生成好了，今晚装起来试试。

soloforce

感谢您的补充，可能是我的代码仓库没及时更新 过后我会做相应修正

POPFAN

版主，我在执行到这一步的时候报错，请教一下怎么解决啊：

root@ubuntu:CubieBoard2# debootstrap --foreign --arch armhf wheezy .

mknod: `/mnt/hgfs/share_folder/CubieBoard2/./test-dev-null': Operation not permitted
E: Cannot install into target '/mnt/hgfs/share_folder/CubieBoard2/.' mounted with noexec or nodev

qj001

很需要这个资料，谢谢楼主！！！！

glg18598

楼主你好，这个是使用的是软浮点吗？硬浮点哪里来支持呢，或更改

glg18598

找到了，在内核配置里面

strongpig

U-Boot 2013.10-rc2-08400-g8a4621c (Nov 08 2013 - 15:22:04) Allwinner Technology
arm-linux-gnueabihf-gcc (Ubuntu/Linaro 4.7.2-1ubuntu1) 4.7.2
GNU ld (GNU Binutils for Ubuntu) 2.22.90.20120919
sun4i# not an uImage at 1600<INTERRUPT>
sun4i#
U-Boot SPL 2013.10-rc2-08400-g8a4621c (Nov 08 2013 - 15:22:04)
Board: Cubieboard
DRAM: 1024 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2013.10-rc2-08400-g8a4621c (Nov 08 2013 - 15:22:04) Allwinner Technology

CPU:   Allwinner A10 (SUN4I)
Board: Cubieboard
I2C:   ready
DRAM:  1 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   emac
Hit any key to stop autoboot:  0
** Unrecognized filesystem type **
302 bytes read in 24 ms (11.7 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** File not found boot/boot.scr **
** File not found boot.scr **
43724 bytes read in 28 ms (1.5 MiB/s)
4517240 bytes read in 231 ms (18.6 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.67
   Created:      2013-11-06  14:26:59 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4517176 Bytes = 4.3 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<6>Initializing cgroup subsys cpu
<5>Linux version 3.4.67 (root@strongpig-virtual-machine) (gcc version 4.7.2 (Ubuntu/Linaro 4.7.2-1ubuntu1) ) #1 SMP PREEMPT Wed Nov 6 22:26:37 CST 2013
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun4i
<6>Memory Reserved:
<6>     SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
Memory policy: ECC disabled, Data cache writeback
<6>sunxi: Allwinner A10 revision C (AW1623/sun4i) detected.
<7>On node 0 totalpages: 262144
<7>free_area_init_node: node 0, pgdat c0853a80, node_mem_map c0a1c000
<7>  DMA zone: 1520 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 193040 pages, LIFO batch:31
<7>  HighMem zone: 528 pages used for memmap
<7>  HighMem zone: 67056 pages, LIFO batch:15
<6>PERCPU: Embedded 7 pages/cpu @c1225000 s7616 r8192 d12864 u32768
<7>pcpu-alloc: s7616 r8192 d12864 u32768 alloc=8*4096<c>
<7>pcpu-alloc: <c>[0] <c>0 <c>
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
<5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 loglevel=8 panic=10
<6>PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>allocated 2097152 bytes of page_cgroup
<6>please try 'cgroup_disable=memory' option if you don't want memory cgroups
<6>Memory: 1024MB = 1024MB total
<5>Memory: 1027060k/1027060k available, 21516k reserved, 270336K highmem
<5>Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc07d061c   (7970 kB)
      .init : 0xc07d1000 - 0xc0801dc0   ( 196 kB)
      .data : 0xc0802000 - 0xc0859c78   ( 352 kB)
       .bss : 0xc0859c9c - 0xc0a1b100   (1798 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>Preemptible hierarchical RCU implementation.
<6>     RCU dyntick-idle grace-period acceleration is enabled.
<6>     Additional per-CPU info printed with stalls.
<6>NR_IRQS:192
<6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>Console: colour dummy device 80x30
<6>Calibrating delay loop...


卡在<6>Calibrating delay loop...，请楼主帮忙分析下

leo1249

您好，我今天剛做完所有的步驟並且插上ＳＤＣＡＲＤ了，但是卻沒有任何畫面，請問這有可能是什麼原因呢？

soloforce

modprobe ump ?

unix_ch

我很喜欢的系统，真的是高手在民间，谢谢